Quantum SDLT 320 User Manual Page 56
- Page / 150
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
CHAPTER 4: Installing Your Tape Drive SDLT 220 and SDLT 320 Product Manual
4-4 March 2004 81-85002-01
4.1.3 Electrostatic Discharge Protection
Several electrical components of the tape system are sensitive to static electricity
and Electrostatic Discharge (ESD). Even a static buildup or discharge that is too
slight to feel can be sufficient to destroy or degrade a component’s operation.
To minimize the possibility of ESD-related damage to the system, we strongly
recommend using both a properly installed workstation anti-static mat and a
properly installed ESD wrist strap. When correctly installed, these devices reduce
the buildup of static electricity that might harm the system.
Observe the following precautions to avoid ESD-related problems:
• Use a properly installed anti-static pad on your work surface.
• Always use a properly fitted and grounded wrist strap or other suitable ESD
protection when handling the tape system and observe proper ESD grounding
techniques.
• Hold the drive only by its sides. Do not touch any components on the printed
circuit board assembly (PCBA).
• Leave the drive in its anti-static bag until you are ready to install it in the
system.
• Place the drive on a properly grounded anti-static work surface pad when it is
out of its protective anti-static bag.
• Do not use the bag as a substitute for the work surface anti-static pad. The
outside of the bag may not have the same anti-static properties as the inside. It
could actually increase the possibility of ESD problems.
• Do not use any test equipment to check components on the PCBA. There are
no user-serviceable components on the drive.
- Copyright 2
- Trademarks 2
- Legal Disclaimers 2
- Contact Information 2
- Revision History 3
- 81-85002-01 March 2004 5
- Table of Contents 7
- 81-85002-01 March 2004 ix 9
- Glossary G-1 11
- List of Tables 13
- List of Figures 15
- Introduction 17
- 1.3 Related Documents 18
- 1.4 Structure of this Manual 18
- 1.5 Conventions 19
- 1.6 For More Information 19
- 1.7 Reader Comments 20
- SDLT 220/320 Product 21
- Information 21
- 2-2 March 2004 81-85002-01 22
- 2.3 SDLT 220/320 Technology 23
- 2.3.2 Pivoting Optical Servo 24
- Likelihood 25
- 2.3.6 Positive Engagement 25
- 2-6 March 2004 81-85002-01 26
- 2.4.1 Data Control Module 27
- 2.4.2 Tape Control Module 28
- 2.4.3 Front Panel Module 29
- 2-10 March 2004 81-85002-01 30
- Features 31
- 2.6 Quantum Diagnostics Tools 32
- 2.7 TapeAlert 33
- 2-14 March 2004 81-85002-01 34
- Drive Specifications 35
- 3.1.1 Interface Type 36
- 3.1.2 Physical Dimensions 36
- 3.1.3 Storage Capacity 37
- 3.1.4 Compression 37
- 3.1.5 Data Integrity 37
- 3.1.7 Head Life and MTBF 38
- 3.1.8 Media Durability 39
- 3.2 Functional Specifications 40
- Feature SDLT 220 SDLT 320 41
- 3-8 March 2004 81-85002-01 42
- 81-85002-01 March 2004 3-9 43
- Pulse Shape 44
- Vibration 44
- 81-85002-01 March 2004 3-11 45
- 3-12 March 2004 81-85002-01 46
- 3.3.1 Air Flow Requirements 47
- 3.3.3 Storage and Shipment 48
- 3.3.4 Altitude 49
- 3-16 March 2004 81-85002-01 50
- 81-85002-01 March 2004 3-17 51
- 3-18 March 2004 81-85002-01 52
- Installing Your Tape Drive 53
- 4.1.1 Safety Precautions 54
- 4.1.2 Handling 55
- 4-4 March 2004 81-85002-01 56
- 81-85002-01 March 2004 4-5 57
- Tape Drive 58
- 81-85002-01 March 2004 4-7 59
- SCSI ID0123 60
- SCSI ID 4 5 (default) 6 7 60
- SCSI ID891011 60
- SCSI ID 12 13 14 15 60
- Denotes Pin 1 orientation 61
- SCSI ID Jumper Across Pins: 62
- 9-10* 7-8 5-6 3-4 1-2 62
- 81-85002-01 March 2004 4-11 63
- 4-12 March 2004 81-85002-01 64
- 81-85002-01 March 2004 4-13 65
- 4-14 March 2004 81-85002-01 66
- 81-85002-01 March 2004 4-15 67
- 4-16 March 2004 81-85002-01 68
- 81-85002-01 March 2004 4-17 69
- 4-18 March 2004 81-85002-01 70
- 81-85002-01 March 2004 4-19 71
- Pin Number Signal Name 72
- 4.4.1 Configuring the Drive 73
- SCSI Cables 74
- AC Power Cable 75
- 4-24 March 2004 81-85002-01 76
- Using Your Tape Drive 77
- 5.1 Power On Self Test 78
- 81-85002-01 March 2004 5-3 79
- 5.3 Updating the Firmware 80
- 5.3.2 Making a FUP/CUP Tape 81
- 5.3.3 Using a CUP/FUP Tape 81
- • Updating the same revision 82
- 81-85002-01 March 2004 5-7 83
- 5-8 March 2004 81-85002-01 84
- 81-85002-01 March 2004 5-9 85
- DLTtape IV [includes DLT 1 86
- (Benchmark)] 86
- SDLT 220 87
- SDLT 320 87
- • The tape is moving 88
- 5.6 Density Selection 89
- 5-14 March 2004 81-85002-01 90
- 81-85002-01 March 2004 5-15 91
- 5-16 March 2004 81-85002-01 92
- 5.7 Troubleshooting 93
- 5-18 March 2004 81-85002-01 94
- 81-85002-01 March 2004 5-19 95
- 5-20 March 2004 81-85002-01 96
- SCSI Description 97
- 6-2 March 2004 81-85002-01 98
- 6.2 SCSI-2 Commands 99
- 6-4 March 2004 81-85002-01 100
- 6.3 SCSI-3 Commands 101
- 6.4 Parity 102
- 6.5 Signal States 102
- 81-85002-01 March 2004 6-7 103
- 6.6 SCSI Signals 104
- Signal Definition 105
- 6.6.2 Signal Bus Timing 106
- 1. Recommended time 107
- 6-12 March 2004 81-85002-01 108
- Regulatory Compliance 109
- 7.1.2 Safety Requirements 110
- 7.2.3 Conducted Emissions 111
- 7.2.4 Radiated Emissions 112
- Type Specifications Comments 113
- 7.3 Acoustic Noise Emissions 114
- Super DLTtape I 115
- Data Cartridge 115
- Super DLTtape Data Cartridges 116
- 81-85002-01 March 2004 A-3 117
- A-4 March 2004 81-85002-01 118
- 81-85002-01 March 2004 A-5 119
- A-6 March 2004 81-85002-01 120
- 81-85002-01 March 2004 A-7 121
- A-8 March 2004 81-85002-01 122
- 81-85002-01 March 2004 A-9 123
- A.5 Loading a Data Cartridge 124
- DLTtape I Data Cartridges 125
- A-12 March 2004 81-85002-01 126
- DLTtape IV Data 127
- Cartridge 127
- B-2 March 2004 81-85002-01 128
- 81-85002-01 March 2004 B-3 129
- B-4 March 2004 81-85002-01 130
- 81-85002-01 March 2004 B-5 131
- B-6 March 2004 81-85002-01 132
- 81-85002-01 March 2004 B-7 133
- B.4 Loading a Data Cartridge 134
- 81-85002-01 March 2004 B-9 135
- B-10 March 2004 81-85002-01 136
- Glossary 137
- G-2 March 2004 81-85002-01 138
- 81-85002-01 March 2004 G-3 139
- G-4 March 2004 81-85002-01 140
- 81-85002-01 March 2004 G-5 141
- G-6 March 2004 81-85002-01 142
- 81-85002-01 March 2004 G-7 143
- G-8 March 2004 81-85002-01 144
- 81-85002-01 March 2004 G-9 145
- G-10 March 2004 81-85002-01 146
- 81-85002-01 March 2004 G-11 147
- G-12 March 2004 81-85002-01 148
- 81-85002-01 A04 150
Related products and manuals for Tape drives Quantum SDLT 320
Tape drives Quantum DLT2700xt User Manual
(345 pages)
(345 pages)
Tape drives Quantum L500 User's Guide
(120 pages)
(120 pages)
Tape drives Quantum DLT4500 User Manual
(360 pages)
(360 pages)
Tape drives Quantum DLT-V4 User Manual
(62 pages)
(62 pages)
Tape drives Quantum PX720 User Manual
(2 pages)
(2 pages)
Tape drives Quantum ACL 2640 Owner's Guide
(68 pages)
(68 pages)
Tape drives Quantum Scalar i6000 User's Guide
(106 pages)
(106 pages)
Tape drives Quantum TC-L32BX-EY User's Guide
(109 pages)
(109 pages)
Tape drives Quantum TC-L53FN-AR User's Guide
(96 pages)
(96 pages)
Tape drives Quantum DLT-V4 Manual
(28 pages)
(28 pages)
Tape drives Quantum DLT 7 Manual
(177 pages)
(177 pages)
Tape drives Quantum DLT 8000 Manual
(408 pages)
(408 pages)
Tape drives Quantum LTO-6 User's Guide
(38 pages)
(38 pages)
© 2020, manymanuals.com. All rights reserved. | 1.906 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals