Quantum SDLT 320 User Manual Page 55
- Page / 150
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
SDLT 220 and SDLT 320 Product Manual CHAPTER 4: Installing Your Tape Drive
81-85002-01 March 2004 4-3
4.1.2 Handling
Damage to the tape system can occur as the result of careless handling, vibration,
shock, or electrostatic discharge (ESD). For more details about ESD, refer to
“Electrostatic Discharge Protection” on page 4-4.
Follow these guidelines to avoid damage to the drive:
• Always observe prescribed ESD precautions.
• Keep the internal drive in its anti-static bag until ready to install.
• Always use a properly fitted wriststrap or other suitable ESD protection when
handling the drive.
• Hold the internal tape drive only by its sides.
• Do not bump, jar, or drop the drive. Use care when transporting the drive.
• Always handle the drive carefully and gently. A drop of ¼ inch onto a bench
or desktop may damage a drive.
• Never place the tape drive so that it rests on its front bezel. Always gently
place the drive flat, printed circuit board (PCB) side down, on an appropriate
ESD-protected work surface to avoid the drive being accidentally knocked
over.
• Do not pack other materials with the drive in its anti-static bag.
• Place the drive in the anti-static bag before placing it in a shipping container.
• Do not stack objects on the drive.
• Do not expose the drive to moisture.
• Do not place foreign objects inside the tape system’s receiver area.
CAUTION: Always handle the tape system with care to avoid
damage to the precision internal components. Do not
place hands inside the tape drive’s receiver area. Hold
the internal tape drive by the sides or the tabletop drive
by the bottom. Never hold either drive by inserting
fingers into the receiver area on the front of the drive.
Damage to the receiver area may occur if the drive is
lifted or carried in this manner.
- Copyright 2
- Trademarks 2
- Legal Disclaimers 2
- Contact Information 2
- Revision History 3
- 81-85002-01 March 2004 5
- Table of Contents 7
- 81-85002-01 March 2004 ix 9
- Glossary G-1 11
- List of Tables 13
- List of Figures 15
- Introduction 17
- 1.3 Related Documents 18
- 1.4 Structure of this Manual 18
- 1.5 Conventions 19
- 1.6 For More Information 19
- 1.7 Reader Comments 20
- SDLT 220/320 Product 21
- Information 21
- 2-2 March 2004 81-85002-01 22
- 2.3 SDLT 220/320 Technology 23
- 2.3.2 Pivoting Optical Servo 24
- Likelihood 25
- 2.3.6 Positive Engagement 25
- 2-6 March 2004 81-85002-01 26
- 2.4.1 Data Control Module 27
- 2.4.2 Tape Control Module 28
- 2.4.3 Front Panel Module 29
- 2-10 March 2004 81-85002-01 30
- Features 31
- 2.6 Quantum Diagnostics Tools 32
- 2.7 TapeAlert 33
- 2-14 March 2004 81-85002-01 34
- Drive Specifications 35
- 3.1.1 Interface Type 36
- 3.1.2 Physical Dimensions 36
- 3.1.3 Storage Capacity 37
- 3.1.4 Compression 37
- 3.1.5 Data Integrity 37
- 3.1.7 Head Life and MTBF 38
- 3.1.8 Media Durability 39
- 3.2 Functional Specifications 40
- Feature SDLT 220 SDLT 320 41
- 3-8 March 2004 81-85002-01 42
- 81-85002-01 March 2004 3-9 43
- Pulse Shape 44
- Vibration 44
- 81-85002-01 March 2004 3-11 45
- 3-12 March 2004 81-85002-01 46
- 3.3.1 Air Flow Requirements 47
- 3.3.3 Storage and Shipment 48
- 3.3.4 Altitude 49
- 3-16 March 2004 81-85002-01 50
- 81-85002-01 March 2004 3-17 51
- 3-18 March 2004 81-85002-01 52
- Installing Your Tape Drive 53
- 4.1.1 Safety Precautions 54
- 4.1.2 Handling 55
- 4-4 March 2004 81-85002-01 56
- 81-85002-01 March 2004 4-5 57
- Tape Drive 58
- 81-85002-01 March 2004 4-7 59
- SCSI ID0123 60
- SCSI ID 4 5 (default) 6 7 60
- SCSI ID891011 60
- SCSI ID 12 13 14 15 60
- Denotes Pin 1 orientation 61
- SCSI ID Jumper Across Pins: 62
- 9-10* 7-8 5-6 3-4 1-2 62
- 81-85002-01 March 2004 4-11 63
- 4-12 March 2004 81-85002-01 64
- 81-85002-01 March 2004 4-13 65
- 4-14 March 2004 81-85002-01 66
- 81-85002-01 March 2004 4-15 67
- 4-16 March 2004 81-85002-01 68
- 81-85002-01 March 2004 4-17 69
- 4-18 March 2004 81-85002-01 70
- 81-85002-01 March 2004 4-19 71
- Pin Number Signal Name 72
- 4.4.1 Configuring the Drive 73
- SCSI Cables 74
- AC Power Cable 75
- 4-24 March 2004 81-85002-01 76
- Using Your Tape Drive 77
- 5.1 Power On Self Test 78
- 81-85002-01 March 2004 5-3 79
- 5.3 Updating the Firmware 80
- 5.3.2 Making a FUP/CUP Tape 81
- 5.3.3 Using a CUP/FUP Tape 81
- • Updating the same revision 82
- 81-85002-01 March 2004 5-7 83
- 5-8 March 2004 81-85002-01 84
- 81-85002-01 March 2004 5-9 85
- DLTtape IV [includes DLT 1 86
- (Benchmark)] 86
- SDLT 220 87
- SDLT 320 87
- • The tape is moving 88
- 5.6 Density Selection 89
- 5-14 March 2004 81-85002-01 90
- 81-85002-01 March 2004 5-15 91
- 5-16 March 2004 81-85002-01 92
- 5.7 Troubleshooting 93
- 5-18 March 2004 81-85002-01 94
- 81-85002-01 March 2004 5-19 95
- 5-20 March 2004 81-85002-01 96
- SCSI Description 97
- 6-2 March 2004 81-85002-01 98
- 6.2 SCSI-2 Commands 99
- 6-4 March 2004 81-85002-01 100
- 6.3 SCSI-3 Commands 101
- 6.4 Parity 102
- 6.5 Signal States 102
- 81-85002-01 March 2004 6-7 103
- 6.6 SCSI Signals 104
- Signal Definition 105
- 6.6.2 Signal Bus Timing 106
- 1. Recommended time 107
- 6-12 March 2004 81-85002-01 108
- Regulatory Compliance 109
- 7.1.2 Safety Requirements 110
- 7.2.3 Conducted Emissions 111
- 7.2.4 Radiated Emissions 112
- Type Specifications Comments 113
- 7.3 Acoustic Noise Emissions 114
- Super DLTtape I 115
- Data Cartridge 115
- Super DLTtape Data Cartridges 116
- 81-85002-01 March 2004 A-3 117
- A-4 March 2004 81-85002-01 118
- 81-85002-01 March 2004 A-5 119
- A-6 March 2004 81-85002-01 120
- 81-85002-01 March 2004 A-7 121
- A-8 March 2004 81-85002-01 122
- 81-85002-01 March 2004 A-9 123
- A.5 Loading a Data Cartridge 124
- DLTtape I Data Cartridges 125
- A-12 March 2004 81-85002-01 126
- DLTtape IV Data 127
- Cartridge 127
- B-2 March 2004 81-85002-01 128
- 81-85002-01 March 2004 B-3 129
- B-4 March 2004 81-85002-01 130
- 81-85002-01 March 2004 B-5 131
- B-6 March 2004 81-85002-01 132
- 81-85002-01 March 2004 B-7 133
- B.4 Loading a Data Cartridge 134
- 81-85002-01 March 2004 B-9 135
- B-10 March 2004 81-85002-01 136
- Glossary 137
- G-2 March 2004 81-85002-01 138
- 81-85002-01 March 2004 G-3 139
- G-4 March 2004 81-85002-01 140
- 81-85002-01 March 2004 G-5 141
- G-6 March 2004 81-85002-01 142
- 81-85002-01 March 2004 G-7 143
- G-8 March 2004 81-85002-01 144
- 81-85002-01 March 2004 G-9 145
- G-10 March 2004 81-85002-01 146
- 81-85002-01 March 2004 G-11 147
- G-12 March 2004 81-85002-01 148
- 81-85002-01 A04 150
Related products and manuals for Tape drives Quantum SDLT 320
Tape drives Quantum DLT2700xt User Manual
(345 pages)
(345 pages)
Tape drives Quantum L500 User's Guide
(120 pages)
(120 pages)
Tape drives Quantum DLT4500 User Manual
(360 pages)
(360 pages)
Tape drives Quantum DLT-V4 User Manual
(62 pages)
(62 pages)
Tape drives Quantum PX720 User Manual
(2 pages)
(2 pages)
Tape drives Quantum ACL 2640 Owner's Guide
(68 pages)
(68 pages)
Tape drives Quantum Scalar i6000 User's Guide
(106 pages)
(106 pages)
Tape drives Quantum TC-L32BX-EY User's Guide
(109 pages)
(109 pages)
Tape drives Quantum TC-L53FN-AR User's Guide
(96 pages)
(96 pages)
Tape drives Quantum DLT-V4 Manual
(28 pages)
(28 pages)
Tape drives Quantum DLT 7 Manual
(177 pages)
(177 pages)
Tape drives Quantum DLT 8000 Manual
(408 pages)
(408 pages)
Tape drives Quantum LTO-6 User's Guide
(38 pages)
(38 pages)
© 2020, manymanuals.com. All rights reserved. | 0.607 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals