Quantum DLT 8000 Manual Page 389
- Page / 408
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Quantum DLT 8000 Tape System E-1
Appendix E
VISUAL INSPECTION PROCEDURE FOR DLTtape
CARTRIDGES
This appendix explains how to visually inspect a DLTtape Cartridge. Damaged cartridges
must not be used.
DLTtape CARTRIDGE GENERAL HANDLING GUIDELINES
• Always keep each tape cartridge in its protective plastic
case when it is not in the tape drive.
• When carrying tape cartridges in their cases, always orient
the cases so that the grooves in the cases interlock. This
prevents the cases from slipping apart and falling.
• Never stack the tape cartridges in a stack of more than five.
• Always observe the proper environmental conditions for
the storage of tape cartridges. Refer to the cartridge
reference card supplied with each cartridge.
• When placing tape cartridges in archival storage, make sure
you stand each tape cartridge vertically.
• Avoid placing tape cartridge near any sources of high
intensity magnetic fields, such as monitor or electric motors.
• Never apply adhesive labels or POST-IT notes on the top,
side, or bottom of your DLTtape cartridge. Only use the
user slide- in type label provided with each cartridge and
slide it over the label slot on the cartridge.
• Do not carry cartridges loosely in a box or any other
container. Allowing cartridges to hit together exposes them
to unnecessary physical shock.
• Do not touch or allow direct contact with tape or tape
leader. Dust or natural skin oils can contaminate the tape
and impact tape performance.
• Do not expose the tape cartridge to moisture or direct
sunlight.
- 8000 Tape System 1
- Product Manual 1
- Table of Contents 10
- REVISION HISTORY 27
- Revision History 28
- Quantum DLT 8000 Tape System 28
- ABOUT THIS MANUAL 33
- CONVENTIONS 35
- FOR MORE INFORMATION 35
- READER COMMENTS 35
- About This Manual 36
- Chapter 1 37
- 1.3 SPECIFICATIONS 38
- 1.3.4 Reliability (Projected) 41
- 1.3.5 Physical Specifications 41
- 1.3.7 Operating Air Velocity 43
- 1.3.9 Altitude 45
- 1.3.10 Acoustic Emissions 46
- 1.3.12 Power Requirements 47
- 1.3.13 Current Requirements 48
- TAPE SYSTEM 55
- 2.2.1 Setting the SCSI ID 58
- 2.2.2 Setting TERM PWR 60
- Front Bezel 61
- 2.3.1 Selecting SCSI ID 71
- SCSI Connectors (2) 72
- 220 / 240 V 74
- AC Power Cord Connector 75
- 2.4 The Tape Cartridge 76
- 2.4.4 Loading a Cartridge 82
- 2.4.5 Unloading a Cartridge 84
- 2.5.1 Unload Button 88
- 2.5.3 Selecting Density 89
- 2.9 Troubleshooting 99
- SCSI DESCRIPTION 103
- 3.2 SCSI Commands 104
- SCSI Description 105
- 3.3 Signal States 107
- 3.4 SCSI Signals 109
- 3.4.2 Signal Bus Timing 110
- 3.5 SCSI Bus Phases 113
- Bus Free Sequence 114
- 3.5.2 ARBITRATION Phase 115
- Arbitration Sequence 115
- 3.5.3 SELECTION Phase 116
- Selection Sequence 116
- Selection Time-Out 117
- 3.5.4 RESELECTION Phase 117
- Reselection Sequence 117
- SCSI ID bit 118
- Reselection Time-Out 120
- 3.6 SCSI Bus Conditions 128
- 3.6.2 Reset Condition 129
- 3.6.3 Queued Unit Attentions 130
- Chapter 4 131
- MESSAGES 131
- Messages 132
- 4.2 Supported SCSI Messages 135
- 4.2.12 NO OPERATION (08h) 141
- SCSI COMMANDS 145
- SCSI Commands 146
- 5.1.1 SCSI Pointers 147
- 5.1.3 Status/Error Reporting 151
- (Continued) 153
- 5.3 ERASE Command (19h) 159
- 5.4 INQUIRY Command (12h) 161
- 5.6 LOCATE Command (2Bh) 179
- 5.7 LOG SELECT Command (4Ch) 181
- Page Code Page Description 183
- 02h Write Error Counter Page 183
- 03h Read Error Counter Page 183
- 32h Compression Ratio Page 183
- LOG PAGE HEADER 184
- LOG PARAMETERS 185
- (continued) 186
- 5.8 LOG SENSE Command (4Dh) 189
- Descriptions (continued) 196
- 5.8.5 TapeAlert Page (2Eh) 200
- TAPE ALERT LOG PAGE HEADER 200
- TAPE ALERT LOG PARAMETERS 201
- Descriptions 210
- 5.9.1 Mode Parameter List 217
- 5.9.8 TAPEALERT PAGE (1Ch) 237
- FORCEDENSITY parameter to 4 247
- 5.10.3 MODE SENSE Mode Pages 258
- Data Field Description 284
- 5.14 READ Command (08h) 304
- 5.16.2 Data Mode 311
- 5.16.3 Descriptor Mode 311
- 5.26 REWIND Command (01h) 353
- 5.28 SPACE Command (11h) 360
- 5.30 VERIFY Command (13h) 363
- 5.31 WRITE Command (0Ah) 364
- 5.32.2 Write Data Mode (010b) 368
- INFORMATION 373
- Appendix B 377
- B.2 Bugcheck Packets 378
- B.2.1 POST Failure Packets 379
- B.2.2 Event Log Packets 379
- UPDATING THE FIRMWARE 381
- 1. POST passed 383
- 2. The drive is unloaded 383
- THE LIBRARY PORT 387
- CARTRIDGES 389
- Cartridge 391
- SYSTEM SCSI COMMANDS 397
- DLT 7000 EMULATION FEATURE 399
- SCSI Bus Differences 403
- Front Panel Differences 405
- *81-60118-04 A01* 408
Related products and manuals for Tape drives Quantum DLT 8000
Tape drives Quantum LTO-6 User's Guide
(38 pages)
(38 pages)
Tape drives Quantum DLT 2500 Service Manual
(114 pages)
(114 pages)
Tape drives Quantum 3U User Manual
(16 pages)
(16 pages)
Tape drives Quantum DLT 8000 User Manual
(7 pages)
(7 pages)
Tape drives Quantum DLT 2500 User Manual
(4 pages)
(4 pages)
Tape drives Quantum DLT 8000 User's Guide
(69 pages)
(69 pages)
Tape drives Quantum LTO 4 User's Guide
(98 pages)
(98 pages)
Tape drives Quantum DLT 7000 Manual
(312 pages)
(312 pages)
Tape drives Quantum DLT VS160 User Manual
(90 pages)
(90 pages)
Tape drives Quantum DLT 2500 Manual
(12 pages)
(12 pages)
Tape drives Quantum PX500 User Manual
(6 pages)
(6 pages)
Tape drives Quantum PowerStor L200 User's Guide
(106 pages)
(106 pages)
Tape drives Quantum DLT 4000 Manual
(300 pages)
(300 pages)
Tape drives Quantum LTO-2 Specifications
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 0.086 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals